Effect of sintering temperature on lightweight aggregates manufacturing from copper contaminated soil

Manufacturing lightweight aggregate (LWA) at high temperature is an effective way to immobilize heavy metals in solid waste. This work investigated the performance and solidification mechanism of LWA prepared from copper contaminated soil. The volume expansion of LWA could reach a maximum of 28%, and its lowest density accounted of 1.5 g/cm³, which met the standard requirements. Optical microscope and micro-CT test illustrated that the addition of Cu leaded to obvious phase separation in LWA. The Cu leaching result of LWA first increased and then dropped with the temperature. The XRD test found that the main formation phase of Cu in LWA were t-CuFe₂O₄ and amorphous phase that they had different acid resistance ability. XPS revealed that the main cause of the agglomeration of liquid phase in LWA was the chain broken reaction between Cu and Si–O tetrahedron. SEM-EDS results showed that the distribution of Cu and Si had a strong correlation, which meant that Cu mostly formed amorphous phase. This work showed the uniqueness of Cu in the high temperature immobilization and pointed out the best immobilization target phase.     

Evolution of the electrical resistivity at rest and during oscillatory shearing of co-continuous morphology (PP/PMMA)/MWCNT systems

In this work, a modified parallel-disks configuration on a strain-controlled ARES rheometer (TA Instrument) was used to study the evolution of the electrical resistivity at rest and during oscillatory shearing of a co-continuous immiscible polymer blend morphology based on polypropylene and /polymethyl(methacrylate) (PP/PMMA) in which various amounts (0–3 wt%) of multiwall carbon nanotubes (MWCNT) were added. The co-continuity of both PP and PMMA phases allowed the buildup of a conductive network due to the preferential localization of the conductive MWCNT at the interface between PP and PMMA. Under a stepwise increase of the oscillatory strain amplitude below a critical value (γ_c = 6.3%), a significant decrease in the electrical resistivity was observed for MWCNT concentrations above the percolation threshold (0.3 wt%) due to the conductive paths induced by both thermal (Brownian) motion and oscillatory shearing. However, for deformation amplitudes higher than γ_c, the resistivity increased due to the destruction of the MWCNT paths induced by the large deformation imposed on the PP/PMMA interface. These observations were also confirmed by the evolution of the storage modulus (G′) which remained constant for γ_c < 6.3% (linear viscoelastic regime), while the values decreased above γ_c due to the destruction of the system's morphology.     

Combinations of Piperine with Hydroxypropyl-β-Cyclodextrin as a Multifunctional System

Piperine is an alkaloid that has extensive pharmacological activity and impacts other active substances bioavailability due to inhibition of CYP450 enzymes, stimulation of amino acid transporters and P-glycoprotein inhibition. Low solubility and the associated low bioavailability of piperine limit its potential. The combination of piperine with 2-hydroxypropyl-β-cyclodextrin (HP-β-CD) causes a significant increase in its solubility and, consequently, an increase in permeability through gastrointestinal tract membranes and the blood–brain barrier. X-ray powder diffraction (XRPD), differential scanning calorimetry (DSC), Fourier-transform infrared spectroscopy (FT-IR), nuclear magnetic resonance (NMR) were used to characterize interactions between piperine and HP-β-CD. The observed physicochemical changes should be combined with the process of piperine and CD system formation. Importantly, with an increase in solubility and permeability of piperine as a result of interaction with CD, it was proven to maintain its biological activity concerning the antioxidant potential (2,2-diphenyl-1-picryl-hydrazyl-hydrate assay), inhibition of enzymes essential for the inflammatory process and for neurodegenerative changes (hyaluronidase, acetylcholinesterase, butyrylcholinesterase).     

武汉市一般人群血清中全氟及多氟烷基化合物浓度及其影响因素研究

目的 了解武汉市一般人群血清中全氟及多氟烷基化合物(PFASs)浓度,探索血清中PFASs浓度水平的影响因素。方法 以在武汉市某医院进行一般体检的人群为研究对象(n=67),通过超高效液相色谱-三重四级杆质谱(UPLC-TQ/MS)联用仪测定外周血清中12种PFASs浓度,采用多元线性回归分析方法分析一般人口学特征和血清中PFASs浓度的关联性。结果 武汉市一般人群血清中12种PFASs的平均浓度水平为11.60 ng/mL。全氟辛烷磺酸及其盐类(PFOS)和全氟辛酸及其盐类(PFOA)的贡献率较大,分别为45.03%和31.86%。男性人群血清中PFOS、PFOA、全氟己基磺酸(PFHxS)、全氟壬酸(PFNA)等主要化合物的浓度高于女性,其β值(95%可信区间)分别为0.708(0.313,1.104)、0.518(0.069,0.967)、0.724(0.388,1.059)和0.684(0.399,0.968)。同时,发现血清中PFOS、PFHxS、PFNA浓度和年龄呈正相关,其β值(95%可信区间)分别为0.062(0.042,0.081)、0.035(0.019,0.052)和0.030(0.016,0.045)。结论 性别和年龄对血清中PFASs浓度有影响,在进行人体PFASs暴露评估中应考虑这些因素。     

菌酶协同改善花生粕的饲用品质

花生粕是重要的蛋白饲料原料，但由于其氨基酸不平衡，特别是精氨酸与赖氨酸比例严重失衡（精氨酸与赖氨酸含量比值在3~4，理想的精氨酸与赖氨酸含量比值为1.0），限制了其在动物养殖中的应用。研究了复合酶预处理结合乳酸菌发酵花生粕对其品质的改善。结果表明：经菌酶协同处理后，花生粕粗蛋白质含量由46.4%提高至506%，大分子蛋白明显降解为小分子蛋白，酸溶蛋白质含量由2.3%提高至17.8%，多肽含量由1.6%提高至15.7%，蛋氨酸和赖氨酸含量分别提高了77.1%和42.0%，精氨酸降解率为18.7%，精氨酸与赖氨酸含量比值从3.7降低至2.1，总酸含量由06%提高到4.7%，其中乳酸含量由0.64 mg/g提高至14.63 mg/g。菌酶协同处理后的花生粕抗氧化性明显增强，其中每克菌酶协同处理后的花生粕对羟自由基的清除能力与171.6 mg VC相当，比花生粕（与47.6 mg VC相当）提高了2.6倍。     

WSN低功耗低时延路径式协同计算方法

针对云计算应用于无线传感器网络(Wireless Sensor Network,WSN)时延敏感型业务时存在的高传输时延问题,提出了一种WSN低功耗低时延路径式协同计算方法。该方法基于一种云雾网络架构开展研究,该架构利用汇聚节点组成雾计算层;在数据传输过程中基于雾计算层的计算能力分步骤完成任务计算,降低任务处理时延;由于汇聚节点计算能力较弱,时延降低将导致能耗增加,WSN工作寿命减短,为此提出能耗约束下的任务映射策略,并利用离散二进制粒子群优化(Binary Particle Swarm Optimization,BPSO)算法解决能耗约束下的时延优化问题。仿真结果表明,在相同的能耗约束下,对比其他算法,基于BPSO算法得出的映射方案能有效降低业务处理时延,满足时延敏感型业务的需求。     

混菌矿化增强再生粗骨料的物理力学性能

为克服单一微生物培养成本高且矿化鲁棒性不足的缺陷，提出了一种混菌矿化增强再生粗骨料物理力学性能的方法.通过筛选矿化效率较高的好氧嗜碱混菌，考察了混菌矿化对再生粗骨料物理力学性能和混凝土抗压强度的影响.结果表明：相同增强时间下，混菌比纯菌呈现出更优异的矿化增强效果；随着混菌矿化增强时间的延长，再生粗骨料吸水率和压碎指标呈现出先减小后增大的趋势，最优增强时间为15 d；采用矿化增强再生粗骨料制备的再生混凝土抗压强度提高幅度达到22.1%.     

公众食品药品网络谣言和虚假宣传辨识能力调查——以贵州省某少数民族自治地区为例

目的 了解公众对网络食品药品谣言信息及虚假宣传甄别能力和行为态度，探索防范谣言传播、维护社会稳定的有效措施和途径。方法 采用随机抽样研究方法，对贵州省某少数民族自治州公众开展食品药品网络谣言及虚假宣传辨识能力、行为态度问卷调查。结果 当地公众食品药品网络谣言及虚假宣传辨识能力总体较低，经济发展落后地区的青少年人群对网络谣言及虚假宣传的辨识能力较弱。大部分公众处理网络食品药品安全信息较为理性，更愿意通过国家监管部门权威网站了解信息，基本具备了确认信息真实性的主观意识，但辟除谣言的行动能力不高。结论 地方党委政府及有关部门应加强食品药品网络谣言和虚假宣传治理，加大当地谣言及虚假宣传的监测和系统性分析研究，有针对性、预判性地进行治理和科普宣传。     

Modification of the wood-plastic composite for enhancement of formaldehyde clearance and the 3D printing application

As the formaldehyde is one of the main indoor pollutants, the purpose of this study is to effectively remove indoor formaldehyde pollution by using environmentally friendly 3D printing ornaments. The wood 3D printing filaments cellulose/polylactic acid composite (Cellu/P) was selected as the starting material, and 3-aminopropyltriethoxysilane (APTES) was used for chemical modification to obtain a series of cellulose composite materials with amino groups. The modified composite materials (APTES@Cellu/P) were characterized by Fourier transform infrared, X-ray diffraction, scanning electron microscope, energy dispersive spectroscopy, thermogravimetric analysis, and mechanical tests, and a formaldehyde removal experiment was performed. The feasibility of 3D printing was evaluated, and the process of 3D printing-functionalized customized ornaments was proposed, and then a school emblem was used for modeling, printing, and surface modification. Compared with the commercially traditional activated carbon, 3D printing-customized ornaments of APTES@Cellu/P material has a better formaldehyde removal effect, and can even avoid the secondary pollution that is common to the activated carbon.